CCTV-MALL JOURNAL

Technical guides

How to Factory Reset Dahua NVR/DVR (Complete Step-by-Step Guide)

10 min read
How to Factory Reset Dahua NVR/DVR (Complete Step-by-Step Guide)
Practical knowledge for your next installation.

How to Factory Reset Dahua NVR/DVR (Complete Step-by-Step Guide)

A factory reset is a critical troubleshooting step for Dahua NVRs and DVRs—whether you’ve forgotten your admin password, encountered persistent software glitches, or need to repurpose the device for a new setup. Resetting your Dahua NVR/DVR to factory defaults erases all custom settings (including passwords, record schedules, network configurations, and alarm settings) and restores the device to its original out-of-the-box state. However, it’s important to approach this process carefully to avoid data loss and ensure a smooth reset. In this complete guide, we’ll walk you through three reliable methods to factory reset your Dahua NVR/DVR, including via the Web 5.0 interface (the most common method), physical reset button, and local monitor interface. We’ll also address common issues like “forgot password” scenarios, troubleshoot reset failures, and share key precautions to protect your data. This guide is tailored for both beginners and installers, with clear, step-by-step instructions compatible with most Dahua NVR/DVR models.

Prerequisites Before You Start

Before initiating a factory reset, take these essential steps to avoid complications and data loss:

  1. Backup Critical Footage: A factory reset will not delete footage stored on your hard drive (HDD) or SD card, but it’s still recommended to back up important recordings to an external device (USB drive, NAS, or computer) beforehand. Follow our previous guide on backing up Dahua footage to ensure you don’t lose critical data[3].
  2. Note Down Current Settings: If you plan to reconfigure the device after reset, write down key settings (IP address, subnet mask, gateway, camera channels, and user accounts) to streamline the post-reset setup.
  3. Admin Access (If Possible): For resets via the Web 5.0 interface or local monitor, you’ll need admin credentials. If you’ve forgotten your password, skip to the “Forgot Password? Reset Dahua NVR/DVR Without Admin Access” section below[4].
  4. Power Stability: Ensure the NVR/DVR is connected to a stable power source (use a UPS if available) to prevent power interruptions during the reset process—interruptions can corrupt the device’s firmware[6].
  5. Check Firmware Version: Confirm your device is running the latest Web 5.0 firmware (update via Setting → System → Firmware Upgrade if needed). Outdated firmware may cause reset failures or glitches[1][2].

Method 1: Factory Reset via Dahua Web 5.0 Interface (Recommended)

The Web 5.0 interface is the most convenient way to factory reset your Dahua NVR/DVR, as it can be done remotely from your computer (as long as you have network access to the device). This method requires admin login credentials. Here’s how to do it:

Step 1: Access the Web 5.0 Interface

  1. Open a compatible web browser (Chrome, Edge, or Firefox) and enter your NVR/DVR’s internal IP address (e.g., http://192.168.1.108, https://192.168.1.108, or https://192.168.1.108:8443). If you encounter the “URL spelling may be incorrect” error, resolve it first by double-checking the IP address, ensuring your computer is on the same network, or using a direct Ethernet connection[9].
  2. Log in with your admin username and password (default username: “admin”; use your custom password—never use default credentials for security).

Step 2: Navigate to the Factory Reset Settings

  1. Once logged in, navigate to the system maintenance menu: Setting → System → System Maintenance (some models may label this Setting → System → Reset or Setting → Maintenance → Factory Reset)[3].
  2. In the System Maintenance interface, locate the Factory Reset option (it may be labeled “Restore Factory Defaults” or “Factory Default Settings”).

Step 3: Initiate the Factory Reset

  1. Click the Factory Reset button—you will see a warning prompt confirming that all custom settings will be erased (footage on storage devices will remain intact).
  2. Read the warning carefully, then enter your admin password to confirm the reset (this prevents accidental resets).
  3. Click OK to start the reset process. The NVR/DVR will automatically reboot—do not power off the device during this time (this can cause firmware corruption)[6].
  4. Wait for the reboot to complete (this may take 2–5 minutes). Once rebooted, the device will be restored to factory defaults.

Method 2: Factory Reset via Physical Reset Button (No Admin Access Needed)

If you’ve forgotten your admin password or cannot access the Web 5.0 interface, you can use the physical reset button on your Dahua NVR/DVR. This method works for most Dahua models and does not require login credentials. Here’s how:

Step 1: Locate the Reset Button

  1. Power off the NVR/DVR and disconnect the power cable.
  2. Locate the reset button (often labeled “RESET” or marked with a small hole) on the front, back, or side of the device. On most models, it’s a small, recessed button that requires a paperclip, toothpick, or reset tool to press[7].

Step 2: Perform the Physical Reset

  1. Insert a paperclip or reset tool into the reset hole and press and hold the reset button firmly.
  2. While holding the reset button, reconnect the power cable to the NVR/DVR (keep holding the button).
  3. Continue holding the reset button for 10–15 seconds (some models require 20–30 seconds) until you see the device’s status light flash rapidly or hear a beep (this indicates the reset has been initiated)[7].
  4. Release the reset button and allow the device to reboot (this may take 2–5 minutes). Once rebooted, the device will be restored to factory defaults, and the admin password will be reset to the default (if applicable—newer models may require activation after reset)[4].

Method 3: Factory Reset via Local Monitor Interface (Direct Access)

If you have a monitor connected directly to your NVR/DVR (via HDMI or VGA), you can perform a factory reset through the local interface. This method is useful if you don’t have network access to the device. Here’s how:

Step 1: Access the Local Interface

  1. Ensure your monitor is connected to the NVR/DVR via HDMI or VGA, and the device is powered on.
  2. On the login screen, enter your admin username and password (if you remember it) to log in. If you’ve forgotten the password, use Method 2 (physical reset) instead[4].

Step 2: Navigate to Factory Reset Settings

  1. Once logged in, right-click on the screen to open the main menu.
  2. Select Main Menu → System → System Maintenance (or Main Menu → Maintenance → Factory Reset on some models)[3].

Step 3: Confirm the Reset

  1. Locate the Factory Reset option and click it. A warning prompt will appear, confirming that all custom settings will be erased.
  2. Enter your admin password to confirm, then click OK to start the reset process.
  3. The NVR/DVR will reboot automatically—do not power off the device during this time. Once rebooted, the device will be restored to factory defaults.

Forgot Password? Reset Dahua NVR/DVR Without Admin Access

If you’ve forgotten your admin password and cannot access the Web 5.0 or local interface, you have two reliable options to reset the password (and perform a factory reset if needed):

Option 1: Password Reset via Dahua Service Portal/APP

  1. If you previously registered your NVR/DVR with the Dahua DMSS app or Dahua Service Portal, open the app and navigate to Device Management → Forgot Password[4].
  2. Follow the on-screen instructions: you may need to scan a QR code from the NVR/DVR’s local interface or enter the device’s serial number (found on the device’s label).
  3. Verify your identity (via phone number, email, or QR code) and set a new admin password.
  4. Once the password is reset, log in with the new credentials and perform a factory reset using Method 1 or 3.

Option 2: Contact Dahua Technical Support

  1. If you haven’t registered the device or the app reset method fails, contact Dahua technical support. Provide them with the device’s serial number (found on the label) and proof of ownership[4].
  2. Support will provide a temporary security code or reset file that you can use to reset the admin password.
  3. Once the password is reset, log in and perform a factory reset as needed.

Post-Reset Setup: What to Do After Factory Reset

After a factory reset, your Dahua NVR/DVR will be in its default state. Follow these steps to reconfigure the device:

  1. Activate the Device (Newer Models): Newer Dahua NVR/DVR models require activation after a factory reset. Create a new admin password (8–16 characters, mix of letters and numbers) to activate the device[4].
  2. Configure Network Settings: Set a static IP address, subnet mask, and gateway (under Setting → Network → TCP/IP) to ensure network access[3].
  3. Add Camera Channels: Reconnect and add your IP cameras (under Setting → Camera → Camera Management). The device may auto-detect cameras on the same network[3].
  4. Set Up Storage: Format your hard drive or SD card (under Setting → Storage → Storage Management) to enable recording—note: formatting will erase all existing footage on the storage device[3].
  5. Reconfigure Custom Settings: Restore your record schedule, alarm settings, user accounts, and other custom configurations using the notes you took before the reset.
  6. Test the System: Verify that cameras are recording, network access works, and remote viewing (via app or Web 5.0) is functional.

Common Reset Issues & Troubleshooting Tips

If you encounter problems during or after the factory reset, use these solutions to resolve them:

1. Reset Button Not Working

Issue: Pressing the physical reset button does not initiate a reset.

Solutions:
Ensure you’re pressing the correct button (check the device manual for location).
Press and hold the button for longer (15–30 seconds) while reconnecting power—some models require a longer hold time[7].
Check if the reset button is stuck or damaged—use a different reset tool (paperclip vs. toothpick) to press it.
Power cycle the device (disconnect power for 1 minute, reconnect) and try again[6].

2. Reset Initiated but Device Not Rebooting

Issue: The reset is confirmed, but the NVR/DVR does not reboot or freezes.

Solutions:
Check power stability—ensure the device is connected to a reliable power source (use a UPS)[8].
Disconnect the power cable, wait 1 minute, then reconnect to force a reboot[6].
If the device still freezes, the firmware may be corrupted. Contact Dahua support for a firmware recovery file[5].

3. Post-Reset Login Failed

Issue: After reset, you cannot log in with the default admin password.

Solutions:
Newer Dahua models do not have a default password—you must activate the device and create a new password after reset[4].
For older models, the default password is “admin” (if not changed). If this doesn’t work, repeat the physical reset process[2].
If the password still fails, use the password reset method via the DMSS app or contact Dahua support[4].

4. Footage Missing After Reset

Issue: After reset, footage stored on the HDD/SD card is missing.

Solutions:
A factory reset does not delete footage—check if the storage device is detected (under Setting → Storage → Storage Management)[3].
If the storage device is not detected, power off the device, re-seat the HDD/SD card, and power back on[8].
If the storage device is corrupted, reformat it (note: this will erase all footage) and restore from your backup[3].

5. Web 5.0 Interface Unreachable After Reset

Issue: After reset, you cannot access the Web 5.0 interface (e.g., “URL spelling may be incorrect” error).

Solutions:
After reset, the device’s IP address reverts to the default (usually 192.168.1.108). Use this IP to access the interface[9].
Ensure your computer is on the same network (192.168.1.x subnet) as the NVR/DVR[9].
Use Dahua’s Config Tool to search for the device’s IP address if you’re unsure[5].

Key Precautions for Factory Reset

  1. Backup Footage First: Always back up critical footage before resetting—even though reset does not delete footage, storage issues can occur during the process[3].
  2. Avoid Unnecessary Resets: Only perform a factory reset when absolutely necessary (e.g., password loss, persistent glitches). Regular resets can shorten the device’s lifespan[6].
  3. Do Not Interrupt the Reset: Powering off the device during reset can corrupt firmware, rendering the device inoperable[6].
  4. Update Firmware After Reset: After reconfiguring the device, update the firmware to the latest version to fix bugs and improve security[1][2].
  5. Secure the New Password: After reset, create a strong, unique admin password and avoid using default credentials to prevent unauthorized access[4].

Final Thoughts: Mastering Dahua NVR/DVR Factory Reset

Factory resetting your Dahua NVR/DVR is a straightforward process when following the correct steps, whether you use the Web 5.0 interface, physical reset button, or local monitor. By taking the necessary precautions (backing up footage, noting settings) and troubleshooting common issues, you can safely reset your device to resolve password issues, glitches, or prepare it for a new setup. Remember, a factory reset erases all custom settings but preserves stored footage—so always back up critical recordings beforehand.

If you’re still encountering issues with the reset process, contact Dahua technical support with your device’s serial number for personalized assistance. With this guide, you’ll be able to reset your Dahua NVR/DVR with confidence, ensuring your surveillance system remains secure and functional.

Have you ever factory reset a Dahua NVR/DVR? Did you encounter any issues, or do you have tips to share? Drop a comment below to help other users master this essential troubleshooting step!

THE EDITORIAL DESK
Editorial team portrait
Representative portrait by Avatarly, CC BY 4.0. Cropped and resized.
CCTV-MALL
Journal

From equipment details
to system decisions.

THE PEOPLE BEHIND THE GUIDES

CCTV-MALL Editorial Team

Surveillance technology. Practical engineering. Clearer decisions.

Our editorial focus spans the complete surveillance system: IP cameras and recorders, PoE networks, video analytics, recording workflows and storage planning. We connect equipment specifications with the questions that arise when selecting, configuring and maintaining a system, helping professional readers work through the details that affect the result.

Written for integrators, installers and procurement teams, our guides draw on manufacturer documentation, model requirements and structured troubleshooting. We explain what to check, which assumptions matter and where a decision needs further verification, so you can build a more informed shortlist, review a configuration and prepare precise questions for your next project.

Configure & integrateIP video, networking and recording workflows
Diagnose & maintainSymptoms, checks and model-specific guidance
Specify & procureEquipment choices, retention and project requirements
FROM RESEARCH TO THE RIGHT EQUIPMENT

Tell us what your project needs.

Models, quantities, availability and options — start with your requirements.

Send an enquiry